LANforge 5.4.1 Released

We’re happy to announce LANforge 5.4.1, that supports a number of new features:

  • Add TR-398 automated WiFi test support.
  • Support /AC on 2.4Ghz on /b/g/n/AC radios (2.4Ghz /AC)
  • Add support for wired traffic test to the Dataplane scenario test.
  • Support 5.2 kernel for latest drivers and kernel features.
  • Support IPSEC interfaces.
  • Support CT850a 2D attenuator turn-table.
  • Support ComXim MT series turn-table (for instance: MT200RUWL20)
  • Improve performance of creating virtual stations, tested 500 stations per /n radio.

Introduction Video

We have a new introduction video that explains what Candela Technologies does and where we fit in the technology landscape. It’s on our homepage and it’s on one of our Candelatech YouTube pages.

Lately we’ve been discussing what other videos we could produce. We’ll definitely produce a very short introduction video. And we’ll definitely make more topical videos about testing scenarios. If you have suggestions for videos about network and WiFi testing you’d like to see, please let us know!

LANforge 5.3.1 Released with WiFi Testing Emphasis

LANforge 5.3.1 has been a serious piece of work to put out. We were dogged by lots of troubles with the QCA firmware for the 802.11ac chipset. Ben put in countless hours combing through stack traces and kernel archives looking for fixes to DMA errors. Amazingly he fixed so many we are able to keep Layer-3 connections alive indefinitely now.

This was also an interesting development period because we got our first pair of Octobox anechoic chambers. These are RF-isolating boxes with RF impeding power and network interfaces at their margins. This was the first time we saw ideal 802.11n throughput in 5Ghz. Like…theoretical ideal. Checked off the list. Ben picked his jaw up off the floor when he saw Isaac’s graphs. Asked him to “do that again!”

Jed spent much time doing 802.11x station roaming experiments. The trick to roaming effectively is to shuffle the roaming requests between radios, not to send sequential roaming (stampeding) requests from a single radio. It would make sense from a CSMCA point of view that a WiFi environment wants to actively listen for activity instead of constantly broadcast. Jed was able to get 30 wifi roaming events a second between two LANforge CT523’s running 164 virtual stations.

This lead us to a great LANforge 5.3.1 release. Lot of work. More planned. Stay tuned.

LANforge 5.2.13 Released

There’s a number of great features in this latest release. Some highlights:

  • The Atheros10k 802.11ac radio driver supports 64 virtual stations, or 63 with one station in monitor mode
  • We offer the new four-module CT704 attenuators, you can now test 4×4 MIMO radios with LANforge
  • a big improvement in Layer-3 UDP performance with low level multi-packet sending. This allows our embedded appliances to emit almost 1Gbps of small packet UDP traffic!
  • Better IPv6 support: router advertisement and dhcpv6 work smoothly in LANforge now.

Here are the release notes for 5.2.13.

And here is a picture of our four-module CT704 attenuator:

CT704 Four module programmable attenuator
CT704 Four module programmable attenuator

Emulate 64 /ac WiFi stations with LANforge

CT525 2U chassis, front
CT525 2U chassis, front

Ben has done impressive work on the Atheros 10K driver. He has really re-organized a lot of code to save every possible bit and byte. We can now emulate 64 wifi stations on the ath10k hardware. If you wanted to test your /ac roll-out, you could do that with 384 virtual stations with a 2U chassis. Or, if you wanted to pack some /n stations in there, you could emulate 792 stations in a similar form factor. (And of course this is all creeping up on the 1200 station pure /n product we presently have.)